Top
রঙ এর গঠন তন্ত্র
কংক্রিট এর সেটিং
ভাল রঙ এর বৈশিষ্ট্য
কখন এবং কিভাবে রং করতে হয়
হ্যান্ড ডাই স্টক (Hand Die Stock)
Need4engineer
Toggle navigation
Home
Blog
Calculation
Addressbook
Estimate
Mathpad
More
Quiz
Ask
Checksheet
Material
Addressbook
Log In
NEED4ENGINEER.COM , ২০১১ সাল থেকে অলাভজনক ভাবে নির্মাণ কাজের বিভিন্ন বিষয় নিয়ে সেবা দিয়ে যাচ্ছে
Civil Quiz 30
In which unit operation objectionable solutes are converted into unobjectionable forms without removal?
gas transfer
solute stabilization
ion transfer
solids transfer
Scientific management is comprised of which of the following two elements?
Method study and job design
Work measurement and job design
Method study and work measurement
Technology assessment and environmental design
Vibrated concrete needs
less
Both A and B
None of the above
high
A Grader which is told by a tractor is known as
elevating grader
motor grader
tractor grader
scraper
In GPS, receivers used are;
electronic clocks
quartz clocks
mechanical clocks
atomic clocks
If the effective plan area of a warehouse is 54 m2, and the maximum height of pile permitted is 2.7 m, then the number of cement bags to be stord is
2700
2500
2000
2200
A small quantity of _______ . % of gypsum is added to prevent flash-setting of the cement.
1 to 2
2 to 3
10 to 12
9 to 10
Which of the following criteria is to be satisfied in selection of member in limit state method?
factored load ≤ factored strength
factored load ≥ factored strength
factored load > factored strength
sometimes factored load < factored strength (or) factored load > factored strength
The dynamic viscosity of the liquid __________ with rise in temperature.
Increases
Decreases
None of these
Remain unaffected
When an external force is not available in a pump, we use a
Heater View Answer
Slip gauge
Hydraulic cylinder
Tail race
What is the maximum shear force acting on the beam shown below.
200 N
8000 N
4000 N
125 N
Chain surveying consists of the arrangement of framework of triangles because a triangle is the only simple plane figure which can be plotted uniquely if
one angle and two sides
three sides
one side and two angles
three angles
In case of non-availability of space due to topography, the most suitable spillway is
chute spillway
shaft spillway
straight drop spillway
ogee spillway
In direct design method of flat slab, total design moment Mo is 945 kNm then negative design moment is
236.25 knm
614.25 knm
708.75 knm
330.75 knm
The vertical members which support the door frame are called
reveals
posts
jambs
styles
The usual percentages of clay and metal in cermet are:
70%, 30%
50%, 50%
60%, 40%
80%, 20%
The equivalent axial load may be defined as the load which produces a stress equal to
bending stress
none of these
maximum stress produced by the eccentric load
maximum stressed fibre
When the effect of refraction is taken into account in levelling, the true staff reading is obtained by subtracting the correction for refraction from the observed staff reading.
Wrong
Right
Both A and B
None of the above
Which of the following conditions is not suitable for the disposal of excreta or sewage?
It is not exposed to the atmosphere
It does not give odour nuisance
It should be accessible for children
The waste does not pollute the ground surface
The cone resistance qc, for sandy silt type of soil is
5
6
2
3.5
___________ wall is used to resist lateral forces like severe wind.
Knee wall
Cavity wall
Infill wall
Shear wall
The ratio of the rate of change of discharge of an outlet to the rate of change of the discharge of the distributing channel, is termed as
sensitivity
proportionality
flexibility
efficiency
Operation of reciprocating motion is done by a source
Energy
Power
Momentum
Inertia View Answer
When orifice discharge the liquid in to some other vessel containing the liquid, and the outlet is partially under liquid the orifice is called
fully submerged orifice
free discharge orifice
partially submerged orifice
large orifice
Dimensions of coefficient of transmissibility are
M'LV
M° L2 T1
M°L°T°
rvfL'T"1
Standard size of wooden sleeper for Broad Gauge track is
250 × 26 × 12 cm
275 × 25 × 13 cm
225 × 23 × 13 cm
180 × 20 × 11.5 cm
Which of the following load combination is not considered for design of roof trusses?
dead load + earthquake load
dead load + live load + wind load
dead load + wind load
dead load + crane load
Pitch of the roof is______
span of roof
ratio of rise to span
rise of roof
none of the above
Removal of parallax, may be achieved by focussing
the objective
the eye-piece
none of these.
the objective and the eye-piece
Which metal is used in cramped joint_____.
Aluminum
Iron
Lead
Copper