Top
রঙ এর গঠন তন্ত্র
কংক্রিট এর সেটিং
ভাল রঙ এর বৈশিষ্ট্য
কখন এবং কিভাবে রং করতে হয়
হ্যান্ড ডাই স্টক (Hand Die Stock)
Need4engineer
Toggle navigation
Home
Blog
Calculation
Addressbook
Estimate
Mathpad
More
Quiz
Galleries
Ask
Checksheet
Material
Addressbook
Log In
NEED4ENGINEER.COM , ২০১১ সাল থেকে অলাভজনক ভাবে নির্মাণ কাজের বিভিন্ন বিষয় নিয়ে সেবা দিয়ে যাচ্ছে
Civil Quiz 96
The sleeper density on main lines is
Both A and B
decreased
None of the above
increased
What is the monthly concentration of solids produced by secondary sewage effluent?
30 mg/l
20 mg/l
40 mg/l
35 mg/l
The cement concrete, from which entrained air and excess water are removed after placing it in position, is called
light weight concrete
sawdust concrete
vacuum concrete
prestressed concrete
The formation of vapour cavities is called
Static pressure drop
Emulsion
Cavitation
Isentropic expansion
The specific gravity of quartz, is
2.9
2.65
2.72
2.85
White washing is done during________
Major repair
Day to day repair
Annual repair
Special repair
The formation width for a double line Broad Gauge track in cutting (excluding drains) as adopted on Indian Railways is
10.82 m
6.10 m
10.21 m
8.84 m
Odours and tastes may result due to the prsence of
micro-organisms either dead or alive
dissolved gases such as oxygen, carbon dioxide, methane etc.
all of the above
mineral substances such as sodium chloride, iron compounds etc.
For a column of height fixed in position and direction both at its top and bottom, its effective length, is
½ l
2l
l
l
The discharge of regulated chemicals into surface waters is controlled by
npdes
cercla
pdac
sara
Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to
Distance of the C.G. of the area from its neutralaxis
Moment of the beam section about its neutral axis
Shear force
Area of the section
The extra width of pavement is provided on
super elevation
width of pavement
length of pavement
horizontal curve
Modulus of rigidity is defined as the ratio of
longitudinal stress and longitudinal strain
lateral stress and lateral strain
shear stress and shear strain
volumetric stress and volumetric strain
Inspiring people to be high performer is called:
Leading
Controlling
Organizing
Planning
Which of the following is not a part of the prismatic compass?
Jewel bearing
Prism cap
Brake pin
Agate cap
Why plate girder is preferred over truss girder?
cost of fabrication of plate girder is high
cost of fabrication of truss girder is high
plate girder requires costly maintenance
higher vertical clearance required for plate girder than truss girder
The efficiency of power transmission through pipe is (where H = Total supply head, and hf = Head lost due to friction in the pipe)
(H - hf )/H
(H + hf )/H
H/(H - hf )
H/(H + hf )
Bottom dump trucks are used for _______ .
all of the above
where material stored under ground
in food processing unit
spread the material in wide area
The minimum & maximum rate of air change is 60 per hour.
1, 30
none of these
30, 60
1, 60
The first step in the planning process is to
None of above
Determine strength and weaknesses
Set an objective
Evaluate alternatives
The natural process in which the oxygen of water of streams is consumed by sewage and at the same time, it is replenished (filled again) by the atmosphere, is known as
deoxidation
oxidation
sedimentation
self purification
The rail section is divided on the basis of
type of rails
spacing of sleepers
speed of trains
gauge of the track
Sensitivity of a soil can be defined as
Percentage of volume change of soil under saturated condition
Ratio of volume of voids to volume of solids
None of the above
Ratio of compressive strength of unconfined undisturbed soil to that of soil in a remoulded state
According to Newton's law of viscosity, the shear stress on a layer of a fluid is __________ to the rate of shear strain.
Equal to
None of these
Directly proportional
Inversely proportional
The angle of the inclined plane at which a body just begins to slide down the plane, is called helix angle.
FALSE
TRUE
None of the above
Both A and B
Expanded metal is
Measured in term of SWM (short way mesh) and LWM (long way mesh)
Manufactured from steel sheets
Used for reinforced concrete in road pavements
All the above
Primary treatment of sewage consists of removal of
large suspended organic solids
floating materials
oil and grease
sandand grit
Pre-chlorination
all of these
improves coagulation
reduces tastes
reduces odours
e-commerce does not include
A business?s interactions with its suppliers
Interactions among the geographically dispersed units of the business
Interactions among the various departments within the business
A business?s interactions with its customers
The ratio of the maximum daily consumption to the average daily demand, is
1.4
1.8
1
1.2